Every finished song leaves my studio with more than one bounce. The full mix is the obvious one. But a mastering engineer wants an unmastered mix with headroom. A music library wants an instrumental. Film and TV clients often want a TV mix with no lead vocal. And nearly all of them want stems too.
Most people learn this the hard way. You deliver one file, you get an email asking for three more, and you open the session again. This post covers how to bounce an instrumental and an unmastered mix in Logic Pro, the mistakes I made for years, and how I do all of it in one pass now.
Why mastering engineers want the unmastered version
If you send a mastered file to a mastering engineer, you've already done their job, badly. A limiter on your master bus squashes the peaks and locks the loudness in place. Nothing they do can bring that dynamic range back.
An unmastered mix for mastering should have three things:
- Headroom. Peaks sitting around -6 dBFS is a common request. Some engineers say -3, some say anything that doesn't clip. There is no magic number, but don't hand them a file that hits 0 dBFS.
- No limiter or maximizer. Take the limiter off. Take off any loudness-targeting plug-in too.
- No clipping and no true-peak overs. Inter-sample peaks can push above 0 dBFS even when the meter looks fine. Keeping headroom solves this.
Many engineers are fine with a gentle bus compressor or EQ left on, if it's part of the sound of the mix. If you're not sure, ask. But the limiter always comes off.
Export at the session's sample rate and at 24-bit. Don't convert, don't dither, don't normalize.
How to bypass master-bus plug-ins in Logic without losing settings
Here is the problem. Your mix was balanced with the limiter on. You need to turn it off for the unmastered bounce, but you want it back for the full mix. You do not want to delete it and lose your settings.
In Logic Pro, go to the Stereo Out channel strip in the mixer. Each plug-in slot has a small power button on its left edge. Click it to bypass the plug-in. The settings stay intact. Click again and it's back exactly as it was.
A few tips:
- If your mastering chain lives on a separate bus feeding the Stereo Out, bypass it there instead.
- Check your output meter before you bounce. With the limiter off, the mix should peak well below 0 dBFS. If it doesn't, pull the Stereo Out fader down. A fader move is fine. The engineer will set the final level.
- Write down what you bypassed. When you come back a week later for a revision, you need to know which state the session is in.
Then File > Bounce > Project or Section, choose WAV, 24-bit, no normalization, no dither. Name it clearly. "SongTitle_Unmastered.wav" beats "bounce 3.wav" every time.
How to mute vocal channels for an instrumental (and the classic mistakes)
An instrumental sounds easy. Mute the vocals, bounce. In practice, this is where most people get burned, because the vocal is almost never on one track.
Vocal reverb and delay returns. You mute the lead vocal track, but the vocal's reverb lives on an aux return. If you pulled the vocal fader down instead of muting it, a pre-fader send is still feeding that reverb, and you get a ghost of the vocal, wet and smeared. Mute the vocal channel itself, and check the returns are silent too.
Sends to parallel compression or effects. Same problem. A vocal sent to a parallel compressor bus will still be audible through that bus if the vocal channel is not actually muted.
The vocal is inside a bus with other things. If your vocals and your synths share a summing stack, muting the vocal track is fine, but muting the vocal bus takes the synths with it. Know your routing.
Backing vocals and ad-libs. Decide what counts as "vocal." For most library deliveries, an instrumental means no voice at all. Backing vocals, harmonies, ad-libs, vocal chops and shouts all come out. If a vocal chop is used as an instrument, ask the client.
Automation. If you automated the vocal mute or vocal fader, your mute may get overridden on playback. Check that the track is actually silent by listening to the instrumental before you send it.
The safest check: solo the vocal group, bounce the instrumental, then play the instrumental and listen for anything that sounds like a person.
The TV mix and no-lead variants that libraries want
Music libraries and sync editors use several versions that are not quite full mix and not quite instrumental.
- TV mix (sometimes called "no lead" or "minus lead"): everything except the lead vocal. Backing vocals stay. This lets a singer perform live on a broadcast with the full track underneath.
- No-lead instrumental with BGVs: same thing by another name, depending on the library.
- Unmastered instrumental: the instrumental, with the master-bus chain bypassed. Some libraries master in-house and want this for consistency across the catalogue.
So a single song often needs four versions: Full Mix, Instrumental, Unmastered Full Mix and Unmastered Instrumental. Plus stems. Plus a TV mix if there are backing vocals. Doing that by hand means bouncing, un-muting, re-bypassing and bouncing again, four to six times, and then checking every file.
How QuickStem does all four versions in one pass
I built QuickStem because I did the above a few hundred times for library deliveries and got sick of it.
QuickStem is a Mac app that drives Logic Pro through Apple's Accessibility API. It scans your session's mixer and routing, finds the stem structure, and shows you what it found. You review the scan, keep the groups it found or combine channels into custom stems, and pick which mix versions you want: Full Mix, Instrumental, Unmastered Full Mix, Unmastered Instrumental, plus any custom mixes you define.
For the unmastered versions, you choose which master-bus plug-ins to bypass. The limiter, the loudness tool, whatever you want. QuickStem bypasses them for those bounces and puts them back afterward.
Then you hit Bounce All. QuickStem solos, bounces and mutes each stem in turn, bounces every mix version, and drops everything into STEMS, MIX DELIVERABLES and DOCUMENTS folders with your file naming applied. It never touches your audio files directly. When it's done, your session is exactly as you left it, and QuickStem verifies that.
Save the setup as a template, and the next song takes a minute to set up. Queue several sessions and let them run overnight.
QuickStem runs on macOS 14 or later with Logic Pro 11 or later, and is signed and notarized by Apple. During the opening sale it's $49 for QuickStem and $79 for QuickStem Plus, down from $69 and $99, until November 30, 2026. Every purchase includes a free Soundwall master. Read more on the QuickStem product page or buy QuickStem now.
FAQ
What level should an unmastered mix peak at? Around -6 dBFS is a safe target and most engineers will be happy with it. The real rule is: no limiter, no clipping, and some room to work. If your engineer gives you a number, use theirs.
Should I leave my bus compressor on for the unmastered mix? If it's part of how the mix sounds and it's not doing heavy limiting, usually yes. Ask the engineer. If you're not sure, bounce one with it and one without, and label them clearly.
Why does my instrumental still have a faint vocal in it? Almost always a reverb or delay return, or a send to a parallel bus. Mute the vocal channels themselves rather than pulling faders, check the returns, then listen to the bounce before you deliver it.
Can QuickStem make a TV mix with backing vocals but no lead? Yes. Define a custom mix that excludes only the lead vocal channels or group. QuickStem will bounce it alongside the standard four versions in the same pass.
Author: John Coggins is the founder of Soundwall Studios in Westlake Village, CA, and the creator of QuickStem. He's a songwriter and producer with over 1,000 works registered with ASCAP and a long-time writer for Extreme Music.