"Export All Tracks as Audio Files" is slow in Logic Pro for one of four reasons: a plug-in that forces real-time rendering, Flex or Varispeed processing on the tracks, a session that is much longer than the music, or a disk that cannot keep up with 40 files being written at once. Each has a different fix. Below is how to tell which one you have, what to change in Logic, and three ways to get stems out faster when the built-in export still takes too long.
Why the export runs slowly
Logic's export is an offline bounce for every track at once. On a clean session it runs many times faster than real time. When it crawls, something in the signal path is holding it to real time or worse.
A plug-in that only renders in real time. Some third-party instruments and effects refuse to run faster than 1x. Hardware-emulating reverbs, anything with an external sidechain, plug-ins with lookahead that reset on every block, and a few older AU wrappers are the usual suspects. If one of these sits on a track, the whole export runs at the speed of the slowest plug-in. Check by soloing one suspect track and running File > Export > 1 Track as Audio File. If a four-minute track takes four minutes, you have found it.
Flex Time, Flex Pitch and Varispeed. Flex processing is calculated on the fly during export. A session with Flex Pitch on a lead vocal and Flex Time on six drum tracks does far more work per sample than a session with none. Varispeed, if it is on in the transport, forces real-time rendering across every track. Turn Varispeed off before exporting; freeze or flatten flexed tracks if you can live with the result.
The project end marker. Export renders from bar 1 to the project end marker, not to the last region. A song that ends at bar 90 inside a project whose end marker sits at bar 300 exports three times as much audio as it needs to, and most of it is silence. Drag the end marker (the right edge of the bar ruler) to a bar or two past your last reverb tail. This is the single most common cause of "why is this taking so long".
Disk and file count. Export writes one file per track at the same time. Forty 24-bit stereo tracks at 48 kHz is about 23 MB per second of music being written in parallel. On an external spinning drive or a nearly full SSD that alone can slow the job. Export to the internal drive, then move the folder.
What to set in the export dialog
Open File > Export > All Tracks as Audio Files and check these before you click Export:
Save Format: WAVE unless the client asks for AIFF.
Bit Depth: 24-bit for delivery. 32-bit float is larger and slower to write; use it only when a mastering engineer asks.
Normalize: Off. On a 40-track session, "Overload Protection Only" adds a scan pass on every file.
Bypass Effect Plug-ins: leave unchecked for stems with their processing printed; check it if you want dry tracks and a faster run.
Include Audio Tail: check it, and make sure your end marker is tight, since the tail is added after the end marker.
Add resulting files to Project Audio: uncheck. It adds a database write per file and clutters the project.
Pattern: set the naming once with the Track Name token so you are not renaming 40 files afterward.
With a tight end marker, Normalize off, and no real-time plug-ins, a typical 40-track, 3-minute session exports in well under a minute on a current Mac.
Three faster ways to get stems out
1. Freeze the heavy tracks first
Right-click a track header and choose Freeze Mode > Pre Fader or Source Only, then press the freeze button. Logic renders the track once, and the export then reads an audio file instead of running the instrument and plug-ins again. Freeze your software instruments and any track with a real-time-only plug-in, then export. Unfreeze afterward if you need to keep editing. This often turns a twenty-minute export into a two-minute one.
2. Export only what the delivery needs
"All Tracks" means all tracks, including the four muted vocal comps, the reference mix and the click. Select just the tracks you are delivering and use File > Export > Selected Tracks as Audio Files instead. Fewer files, less disk time, and no cleanup. If your delivery is grouped stems rather than one file per track, see the guide on exporting summing stacks as single stems: How to export summing stacks as single stems in Logic Pro.
3. Use Bounce for grouped stems instead of Export
Export gives you one file per track. If the library or mixer wants eight grouped stems plus a full mix and an instrumental, Export leaves you with 40 files to combine by hand. Bounce (File > Bounce > Project or Section) renders the main output, so you solo a group, bounce, solo the next, bounce. Each bounce is a short offline render of only the soloed material, which is faster than rendering every track when you only need eight files. The trade-off is the manual soloing, which is where mistakes creep in. The comparison is worked through here: Bounce in place vs export tracks in Logic Pro.
Where QuickStem fits
If your deliveries are grouped stems plus mix versions, the slow part is rarely the render. It is the soloing, bouncing, muting, naming and filing, repeated for every stem and every version. QuickStem is a Mac app that does that sequence for you. It scans the Logic mixer and routing, shows the stem groups it found, lets you keep them or combine channels into custom stems, and then drives Logic's own bounce for each one through Apple's Accessibility API. You choose the mix versions (Full Mix, Instrumental, Unmastered Full Mix, Unmastered Instrumental or custom), pick which master-bus plug-ins to bypass for the unmastered versions, set the file naming once, and press Bounce All. Output lands sorted into STEMS, MIX DELIVERABLES and DOCUMENTS folders. It never touches your audio files and verifies the session is unchanged when it finishes. A batch queue runs several sessions overnight, so a slow render stops being your problem.
QuickStem needs macOS 14 or later and Logic Pro 11 or later, and is verified on Logic Pro 12. It is $49 during the opening sale (regular $69), with QuickStem Plus at $79 (regular $99). One licence covers two Macs. More at the QuickStem product page.
FAQ
Why does Logic Pro export all tracks in real time?
A plug-in that cannot render faster than real time, or Varispeed being on, forces the whole export to 1x. Solo tracks one at a time and export each to find the plug-in, then freeze that track before exporting.
Does the project end marker affect export time?
Yes. Export renders from the start of the project to the end marker, so a marker far past the end of the song exports minutes of silence. Drag it to just after the last tail.
Is Export or Bounce faster for stems in Logic Pro?
Export is faster when you want one file per track. Bounce is faster when you want a handful of grouped stems, because each bounce renders only the soloed material.
Why are my exported stems different lengths?
Usually Include Audio Tail combined with regions that end at different points, or a cycle range that was on. See Logic Pro stems coming out different lengths.
Author: John Coggins is the founder of Soundwall Studios in Westlake Village, CA, and the creator of QuickStem. He's a songwriter and producer with over 1,000 works registered with ASCAP and a long-time writer for Extreme Music.